Cargolog Online
Cargolog Connect

LED functions

The LEDs on the Cargolog® device, 2nd Gen have several sequential modes to report different situations. Depending on how the LEDs light up when you press the button, you will know the mode of the Cargolog® device. Press the button with your finger, a pen, or a similar object.

Contact us
Download PDF instructions
LED functions

LED modes

Activation
Mode A
Mode B
Mode C
Mode D
Mode E
Mode F

Mode:

Initiating the recording period

To start the recording for the Cargolog® device with pre-configured settings on the 2nd Gen device, follow these steps:

  1. Press and hold the button for 15-20 seconds (keep the button pressed throughout the entire sequence).
  2. All LEDs will illuminate and then turn off.
  3. The LEDs will sequentially light up one at a time from right to left, indicating the start of the recording (Angle, Temp, Rh, Acc).
  4. Release the button after the sequence completes to initiate the measurement period.
actication mode for cargolog impact and shock recorder system designed by mobitron made in sweden

Mode A:

Not programmed

If the Cargolog® device has not been programmed. To check its status:

  1. Press the button, and observe all LEDs lighting up for 3-4 seconds.
  2. After releasing the button, note that all four LEDs will blink ten times within 3-4 seconds.

Please be aware that there may be a brief delay between releasing the button and the commencement of the LED blinking sequence.

Mode A Ready but not programmed

Mode B:

Programmed but not active

The Cargolog® device is programmed but not started.

  1. While the button is pressed, all LEDs on the Cargolog® device illuminate for 3-4 seconds. 
  2. Upon releasing the button, all LEDs go out. 

The Cargolog® device has been programmed but is not actively recording or monitoring impacts. It remains in a standby or inactive mode. This separation between programming and activation allows users to set up the device with specific parameters before putting it into active use.

Mode B Programmed not started

Mode C:

Active with no exceeded alarm limits

The Cargolog® device is active and operational, with a recording exceeding predefined alarm limits. To verify its status:

  1. Press the button, and observe all LEDs lighting up for 3-4 seconds while the button is held.
  2. Release the button to trigger two sequential sequences: the LEDs representing angle, temperature, and humidity illuminate one at a time from right to left.

This functionality is available with Firmware version ≥2.8.1.0. Check the firmware by connecting to the software. For more information, see the manual.

Mode C programmed being started

Mode D:

Active with exceeding alarm limits

The Cargolog® device is active and operational, with a recording exceeding predefined alarm limits. To verify its status:

  1. Press the button, and observe all LEDs lighting up for 3-4 seconds while the button is held.
  2. Release the button to trigger two sequential sequences: the LEDs representing angle, temperature, and humidity illuminate one at a time from right to left.
  3. The LED corresponding to the sampling channel that exceeded the alarm limit will stay lit for 5 seconds.

This functionality is available with Firmware version ≥2.8.1.0. Check the firmware by connecting to the software. For more information, see the manual.

Mode D Started Running 1 limit exceeded ver2

Mode E:

Measuring cycle ended with no exceeded alarm limit

The measurement cycle has concluded, and sampling has ended, with no exceeding alarm limits. Check the status as follows:

  1. Press the button, and all LEDs illuminate for 3-4 seconds.
  2. The acceleration LED blinks for 4-5 seconds after releasing the button.
Mode E Programmed Started Cycle completed No limits exceeded

Mode F:

Measuring cycle ended with exceeded alarm limits

The measurement cycle has concluded, and sampling has ended, with a recording of exceeding predefined alarm limits. Verify the status as follows:

  1. Press the button, and all LEDs illuminate for 3-4 seconds.
  2. Upon releasing the button, the LED corresponding to the measuring channel that exceeded the alarm limit will stay lit for 5 seconds.
  3. The acceleration LED blinks for 4-5 seconds.
Mode F Programmed Started Cycle completed limits exceeded

Search product

Software

Manual

Brochures

Application

All tutorials

You can find our tutorials here.